Work
These are all 26 models. Each kind of model also has a page of its own.
Fitness
AnkleGrid balance board
A split balance board with a rib grid and twist-lock pegs that stack for height.
Home
Gridfinity-compatible storage bins
Drawer bins and baseplates that fit the open Gridfinity system, in any size.
Toys and RC
Articulated fire dragon
A sculpted fire dragon whose captive joints print in place and never come loose.
Home
Folding phone and tablet stand
A slim card that folds into a sturdy stand and folds flat again for your pocket.
Home
Spiral planter and vase
A spiral-ribbed planter with a drip tray, and a matching vase that prints in spiral mode.
Electronics
Round robot chassis
A two-wheel robot base that spins in place, with plates for an Arduino Uno, an ESP32 or a Pico.
Electronics
Snap-lid board enclosure
A soft, rounded case for an Arduino Uno, an ESP32 or a Pico, with a lid that snaps on.
Halloween
Light-up pumpkin lantern
A deeply carved jack-o'-lantern lit by an LED ring and a Raspberry Pi Pico.
Electronics
Animatronic eyes with lids
Eyes that glance about and blink behind a sculpted face, with upper and lower lids on their own servos.
Halloween
Hannya demon mask
A full-face hannya with a wide fanged grin, tusks and gold crescent horns, sized to a real face.
Halloween
Ram's horns
A real ram's horns from a museum scan, curling back to the ears from clips that zip-tie to any headband.
Halloween
Visored sallet knight's helmet
A real 15th-century German sallet from a museum scan, with a visor that lifts, sized to your head.
Halloween
Knight's sword and wand
A medieval arming sword measured from a scan of a real one, on a fibreglass core, and a carved spiral wand, both printed without supports.
Electronics
4 inch FPV quad frame
An organic 4 inch FPV frame in PETG with bolt-on arms, so a crash costs one arm, not the frame.
Toys and RC
Self-righting RC speed boat
A 472 mm deep-V racer with a fastback canopy and rear wing that rights itself, printed in vase mode.
Toys and RC
Pylon racer RC plane
A 716 mm low-wing pylon racer in foaming PLA for a 2306 quad motor on 4S.
Toys and RC
5 inch speed quad frame
A printed 5 inch speed quad of my own design, built round its thrust axis like the record breakers.
Toys and RC
Axolotl flexi keychain
A pink chibi axolotl that wiggles on four print-in-place joints and hangs from your keys.
Toys and RC
Cat flexi keychain
An orange chibi cat with white paws that wiggles on four print-in-place joints and hangs from your keys.
Toys and RC
Dachshund flexi keychain
A long black-and-tan sausage dog that wiggles on five print-in-place joints and hangs from your keys.
Toys and RC
Capybara flexi keychain
A calm round capybara with a yuzu on its head that wiggles on three print-in-place joints.
Toys and RC
Octopus flexi keychain
A purple chibi octopus whose four tentacles wiggle on eight print-in-place joints.
Toys and RC
Gecko flexi keychain
A green day gecko with yellow spots and toe pads that wiggles on five print-in-place joints.
Toys and RC
Shark flexi keychain
A smiling cyan shark that wiggles on four print-in-place joints and hangs from your keys.
Toys and RC
Otter flexi keychain
A sea otter floating on its back, holding a mussel, that wiggles on four print-in-place joints.
Toys and RC
Fox flexi keychain
An orange chibi fox with a big bushy tail that wiggles on four print-in-place joints.